Classy Pipe & Tube bending machine is a new pipe bending tool with a bending function and lifting function. The control panel of the Classy Pipe&Tube bending machine has the operation mode of the China Pipe & Tube bending machine, including manual mode, semi-automatic mode, and test machine mode. Let’s take a look at the Classy Pipe&Tube bending machine in detail. The working method of the machine.
1.Test mode
It works first after pedaling. When it is in working condition, the pedal stops working again, and if you need to continue working, pedal again, press the stop button to stop working.
Introduction of China Pipe & Tube bending machine test machine: The test machine can only be used for the empty operation of the device, not for processing! Please be careful to test the engine only by eliminating the need for all pedaling movements in the first place. The other action process is the same as in official production. The work will rot until the count value equals the set number or the button stops.
2.Semi-automatic mode
It works first after pedaling. In the working state, pedaling again will pause the action, and if you need to work, pedal again, press the stop button to stop working. One workflow of the ChinaPipe&Tube bending machine allows the pedal work to be completed twice, that is, the first time the work is taken, and the tube is taken once.
3.Manual mode
Enter the manual screen. Press the keys on the side of the action introduction to perform various actions accordingly. The end of the action is determined by the set time and is displayed as “already in place.”
4.Fully automatic mode
Work first after pedaling. If you are in working condition, pedal again to pause work. If you need to continue working, pedal again and press the stop button to stop working. One workflow of the ChinaPipe&Tube bending machine needs to be completed once, that is, the first time the work is done.
Classy Pipe & Tube bending machine wrinkled at the bend.
Classy Pipe & Tube bending machine now occupies an important space with rapid development. The construction of public railways, pipe laying, and construction of boilers, bridges, ships, furniture, decoration, etc., are all inseparable from the Classy Pipe & Tube bending machine. There are wrinkles in different parts of the bending of the Classy Pipe&Tube bending device. Below, we introduce the causes and treatment methods of wrinkling at the end of the Classy Pipe & Tube bending machine
Causes of wrinkles at bends:
- The pipe fitting is thin and not guided after the die.
- The guide die is not placed in the diameter die.
- The slope of the guide die is too oblique.
- The guide die is not pressed.
- The guide die is damaged.
How to deal with it:
- Add a guide mold.
- Adjust the center position of the guide dies.
- Adjust the slope of the guide passes.
- The guide die is tightened forward.
- Revise the guide mold again.
Reasons for oil leakage
Classy Pipe & Tube bending machine in the modern pipe bender machinery industry combines CNC technology and traditional pipe bending technology and emerge with the development of the machine tool industry. The China Pipe & Tube bending machine has a high degree of automation and increased efficiency and is suitable for bending complex space turns quickly and accurately.
During the use of the Classy Pipe&Tube bending machine, there will be oil leakage from the cylinder, so what is the reason for the oil leakage in the Classy Pipe & Tube twisting machine cylinder? The possible causes are as follows:
It may be that the sealing ring of the cylinder is not replaced for a long time, and the sealing performance has become worse; the life of the sealing ring is generally two years; if two years have not been replaced, the sealing ring of China Pipe & Tube bending machine, then the sealing ring must be more seriously worn, so that the sealing performance is not good enough, there may be oil leakage in the cylinder. Just replace the seal or cylinder with a new one.
The bending cross-section deformation rate of the Classy Pipe&Tube bending machine does not meet international standards. The existence of this problem can easily lead to the failure of the chain, control circuit, etc.; as long as the bending section deformation rate of the Classy Pipe&Tube bending machine is controlled within a reasonable range, the problem can be solved.
If there is oil leakage in the cylinder of the Classy Pipe & Tube bending machine, be sure to find out and solve the problem in time so as not to affect the normal use of the Classy Pipe & Tube bending machine.
The main power of the China Classy Pipe & Tube bending machine relies on the hydraulic oil pump to input hydraulic oil. The hydraulic solenoid valve provides the dominant hydraulic power to the cylinder piston to realize the operation of each part. It was originally set to 90° under normal conditions, but after the oil temperature rises, there may be an angle deviation of 100° or 70°. How can I solve this situation? How to prevent angular variation in the oil temperature of the Classy Pipe & Tube bending machine? China Pipe&Tube turning machine factory will tell you how to do it!
Hydraulic oil runs back and forth in the oil pump motor, then to the solenoid valve push to achieve high-pressure input. In this mode, the oil temperature will soon rise, especially in the hot summer; all kinds of classy pipe & tube bending machines, including metal circular, saw automatic machine pipe cutting machine and pipe shrinking machine will appear, oil leakage can not lock oil so that the head drop on the pipe cutting machine, pipe shrinking machine When there is insufficient pressure, Classy Pipe & Tube bending machine is a relatively advanced equipment, which can fully automatic feeding, automatic corner, and automatic forming. With the continuous development of the fully automatic industry, Classy Pipe & Tube bending machine has high precision, stable performance, simple and safe operation. It is widely used in the bending processing of pipe fittings such as aerospace, automobiles, locomotives, motorcycles, ships, petrochemicals, electric power, natural gas, nuclear industry, boilers, vehicles, fitness equipment, sporting goods, etc. Let’s take stock of the three advantages of the full classy Pipe & Tube bending machine.
High positioning accurac
The positioning accuracy is very high, and it can be positioned very accurately. China Pipe & Tube bending machine factory can quickly find out where the fault is displayed during repair and rapidly repaired.
High work efficiency and cost-saving
All the steps can be done by the machine itself, and it doesn’t require too many people to operate it, so that you can save a part of the cost.
Operators can pass brief training
you will be able to work,Since the operation of the Classy Pipe & Tube bending machine is very simple, the operator can go to work after brief training, which is very time-saving.
These are the three advantages of the Classy Pipe & Tube bending machine, which is an important reason why more and more people choose it for their jobs.
If the error is large, the China Pipe&Tube bending machine factory recommends that you add some hydraulic oil appropriately when the summer comes and turn off the machine when the Classy Pipe & Tube bending machine is operating.
